Verde Eon XL 20-inch BMX bike — a 21-inch top tube for riders who need more room:

Key features

• Suggested rider height: Approx. 180 cm and above
• Wheel size: 20 in
• Top tube length (TT): 21 in
• Cranks: Three-piece chromoly, 170 mm
• Weight: Approx. 11.47 kg
• Riding style: Freestyle BMX
• Rider level: Intermediate

Check the fit before choosing

If a shorter BMX feels cramped, the Eon XL gives you a 21-inch top tube to compare with your current bike. That is the frame measurement; the wheels are 20 inches. The suggested rider height is around 180 cm and above, but reach, frame clearance and your preferred riding position matter too.

A freestyle setup without gear changes

The Eon XL is intended for intermediate freestyle riders, with street and skatepark riding in mind. Its three-piece chromoly cranks measure 170 mm, and the bike has a U-brake operated by a two-finger lever. Have the brake adjusted so you can reach and use the lever comfortably.

Know what the frame is made from

The top tube and down tube are 4130 chromoly, with 1020 hi-ten steel elsewhere and gusset reinforcements. The fork pairs a chromoly steerer with tapered hi-ten legs. A 9-inch-rise hi-ten bar and top-load aluminium stem form the cockpit.

The build has 20 x 2.4-inch tyres, 150 mm grips, nylon pedals and a saddle/post combo. The listed weight is approximately 11.47 kg. Compare the size and contact points before deciding whether it suits your riding.

Verde Eon XL 20-inch BMX bike — specifications:

Sizing, weight and other details:

• Suggested rider height: Approx. 180 cm and above
• Wheel size: 20 in
• Weight: Approx. 11.47 kg
• Riding style: Freestyle BMX
• Rider level: Intermediate

Frame geometry:

• Top tube length (TT): 21 in
• Chainstay length (CS): 13.5 in
• Head tube angle (HA): 74.5°

Cranks:

• Cranks: Three-piece chromoly, 170 mm

Frame:

• Frame: 4130 chromoly top tube and down tube, 1020 hi-ten steel elsewhere; gusset reinforcements

Fork:

• Fork: Hi-ten steel legs, chromoly steerer, tapered legs

Handlebars:

• Bar: Hi-ten steel, 9 in rise

Stem:

• Stem: Aluminium, top load

Wheels and rims:

• Wheels: 20 in, 36H

Tyres:

• Tyres: 20 x 2.4 in

Bottom bracket:

• Bottom bracket: Mid BB, 19 mm

Chain:

• Chain: PYC 410

Brakes and controls:

• Brake: U-brake, two-finger lever

Saddle and seatpost:

• Saddle and seatpost: Combo, aluminium post

Grips and bar ends:

• Grips: 150 mm

Pedals:

• Pedals: Nylon

Safety while riding

Freestyle BMX riding puts high loads through the bike during tricks, jumps and landings. No bike is indestructible: parts can wear out or become damaged. Check the frame, fork, bars, wheels, axles, cranks, pedals, brakes and bolted connections before every ride. Inspect the bike after a hard impact and stop riding if you find looseness, cracks or damage. Have any problem checked and repaired before riding again.

Wear a properly fitted helmet and suitable protective pads. Read our important information before buying and riding a BMX bike for assembly, servicing and riding checks.

Important information about your new bike

• Read the instructions and warranty supplied with the bike before riding.
• The bike is delivered approximately 90% assembled for shipping.
• Before the first ride, fit the pedals, saddle and handlebars, and the front wheel where required. Follow the assembly instructions and check all components.
• Have a professional bike workshop carry out a pre-ride inspection. This is a paid service; keep the receipt as proof for the manufacturer’s warranty and follow the warranty terms supplied with your bike.

The manufacturer’s warranty is separate from your statutory consumer rights. Continue to inspect and service the bike throughout its use.

Frame geometry diagram