Dartmoor Gamer Intro 24-inch junior dirt bike — a smaller single-speed setup for dirt and pumptrack sessions:

Key features

• Suggested rider height: Approx. 140–160 cm
• Wheel size: 24 in
• Frame: Hydroformed 6061-T6 aluminium, dirt geometry
• Fork: RST Dirt RA, 100 mm travel, oil damping
• Drivetrain: Single speed, 32T chainring and 14T freewheel
• Cranks: Three-piece aluminium
• Brake: Mechanical disc, 160 mm rotor
• Weight: Approx. 13.25 kg

A 24-inch setup for younger dirt riders

The Gamer Intro 24 is sized around 24-inch wheels and a 710 mm Tornado bar. The suggested rider height is around 140–160 cm. Check your child’s reach, clearance over the frame and ability to operate the brake controls before choosing; height alone does not decide fit.

No gear changes to manage

A 32T chainring drives the 14T freewheel, so there is one gear to pedal and you can coast between efforts. The three-piece aluminium cranks and Dartmoor Core chain complete the drivetrain.

The hydroformed aluminium frame is paired with an oil-damped RST Dirt RA fork with 100 mm of travel. A short Viper stem and Slim Combo saddle complete the riding position. Choose features that suit the rider’s ability and follow the fork’s setup instructions.

Check the brake before each session

The mechanical disc brake uses a 160 mm rotor. Have it adjusted and test its operation before riding. Double-wall Shark rims carry Kenda K-Rad 24 x 2.3-inch tyres.

An adult should help choose a suitable helmet, protective equipment and riding area, and check the bike before use. The listed weight is approximately 13.25 kg.

Dartmoor Gamer Intro 24-inch junior dirt bike — specifications:

Sizing, weight and other details:

• Suggested rider height: Approx. 140–160 cm
• Wheel size: 24 in
• Weight: Approx. 13.25 kg

Frame:

• Frame: Hydroformed 6061-T6 aluminium, dirt geometry

Fork:

• Fork: RST Dirt RA, 100 mm travel, oil damping

Drivetrain:

• Drivetrain: Single speed, 32T chainring and 14T freewheel

Cranks:

• Cranks: Three-piece aluminium

Brakes and controls:

• Brake: Mechanical disc, 160 mm rotor

Handlebars:

• Bar: Dartmoor Tornado, 710 mm width, 31.8 mm clamp

Stem:

• Stem: Dartmoor Viper Short

Wheels and rims:

• Rims: Dartmoor Shark, 24 in, double wall

Tyres:

• Tyres: Kenda K-Rad, 24 x 2.3 in

Chain:

• Chain: Dartmoor Core

Saddle and seatpost:

• Saddle: Dartmoor Slim Combo
• Seatpost: 27.2 mm

Grips and bar ends:

• Grips: Dartmoor Evolution

Pedals:

• Pedals: Dartmoor Candy

Hubs and guards:

• Hubs: Cartridge bearings

Rear hub and driver:

• Rear hub: 135 x 10 mm axle, 14T freewheel

Warranty registration

Register your purchase to activate the stated two-year manufacturer’s warranty, following the terms supplied with your bike. Keep the purchase receipt and the receipt for the initial professional service.

Replacement parts under a claim

If a claim is accepted and the original product or part is unavailable, the manufacturer or seller may provide an equivalent replacement. Its appearance or construction may differ, while its functional specification remains suitable for the original intended use. This does not affect your statutory consumer rights.

Safety while riding

Dirt jumps, tricks and landings put high loads through the bike. Falls and impacts can damage components. No bike is indestructible: parts can wear out or become damaged. Check the frame, fork, bars, wheels, axles, cranks, pedals, brakes and bolted connections before every ride. Inspect the bike after a hard impact and stop riding if you find looseness, cracks or damage. Have any problem checked and repaired before riding again.

Wear a properly fitted helmet and suitable protective pads. Read our important information before buying and using a bike for assembly, servicing and riding checks.

Important information about your new bike

• Read the instructions and warranty supplied with the bike before riding.
• The bike is delivered approximately 90% assembled for shipping.
• Before the first ride, fit the pedals, saddle and handlebars, and the front wheel where required. Follow the assembly instructions and check all components.
• Have a professional bike workshop carry out a pre-ride inspection. This is a paid service; keep the receipt as proof for the manufacturer’s warranty and follow the warranty terms supplied with your bike.

The manufacturer’s warranty is separate from your statutory consumer rights. Continue to inspect and service the bike throughout its use.